Radial Reamp Station Combined Studio DI and Reamp Box

Radial Reamp Station: Capture Dry, Reamp Later, in One Box

The Radial Reamp Station is a combined studio direct box and reamping unit, pairing an active DI that captures a clean dry track with a passive transformer reamper that sends it back out to real amps and pedals. In one desktop chassis it covers both halves of modern tone-shaping: record the pure, unprocessed sound of your instrument now, then re-tone that performance through any amp or pedalboard whenever inspiration strikes. For the producer who hates committing to an amp sound before the mix, it is a small box that removes a big regret.

What Reamping Is, and Why It Changes How You Track Guitar

Reamping is a studio technique worth learning because it separates performance from tone. The idea is simple: first you record a clean DI track, the raw, dry output of your guitar or bass with no amp involved, capturing the perfect take. Later, at mixdown, you play that dry track back out through a reamper into a real amplifier or pedalboard and record the result. Suddenly the amp choice, the settings, even the room are all decisions you can revisit endlessly, long after the player has gone home. You never have to nail the tone and the take at the same moment again.

The DI Side: A J48-Derived Active Direct Box

Capturing a great dry track takes a great DI, so the Reamp Station's input stage is derived from the acclaimed Radial J48. It presents a high 220 kilohm input impedance that preserves every bit of a pickup's detail, then delivers a clean, balanced 185 ohm output straight to your interface across a wide 5 Hz to 20 kHz response. A buffer switch, pad, and ground lift let you optimize the capture and kill any hum, so the dry track you record is a faithful, pristine starting point for whatever tone you build later.

The Reamp Side: The Passive JCR Transformer

Sending a recorded track back to an amp is not as simple as plugging in a cable: the levels and impedances are all wrong, and getting them mismatched brings noise and tone loss. The Reamp Station solves this with a passive, US-made JCR transformer. It steps your interface's line-level playback back down to the instrument level and impedance an amp expects, so the amplifier or pedal sees exactly what it would from a guitar plugged straight in. Because it is passive, the reamp path needs no power and adds its own transformer warmth to the signal.

Level and Impedance Matching Done Right

The details are what make reamping sound natural instead of thin. The JCR reamp side presents a 1.4 kilohm input and a 5.1 kilohm output, a carefully chosen match that lets a line-level signal drive a guitar amp's front end the way a real pickup does: same feel, same touch response, same interaction with the amp's input stage. A three-position filter shapes the reamped feed, and a mute switch silences the output so you can re-patch amps without a pop. It is the difference between a reamp that fools the ear and one that obviously came out of a computer.

Connections and Controls for Any Workflow

The Reamp Station is built to drop into any studio. The reamp input accepts 1/4-inch, XLR, or 3.5 mm sources, so you can feed it from an interface, a console, or even a phone. The DI takes a 1/4-inch instrument input, and outputs include 1/4-inch and XLR plus a DI Thru. A pair of Link In and Link Out jacks let you chain multiple units or amps to drive several rigs from a single dry track. The DI side runs on standard 48V phantom power from your interface, while the reamp side stays fully passive.

Where the Reamp Station Fits Your Workflow

The most common use is reamping guitars and bass at mixdown, auditioning amp after amp against a finished mix until one sits perfectly. But the box goes further: capture a dry track while monitoring a live amp so you keep the vibe and the flexibility, run effects reamping to send stems out through hardware pedals and back, or use the Link jacks to drive two amps at once for layered, parallel tones. Any time you want to shape tone with real hardware after the performance is done, this is the hub.

Who the Reamp Station Is For

The Reamp Station is for the home-studio guitarist who wants to stop guessing at amp tones during tracking; for the producer who reamps stems through outboard gear and needs pristine, properly matched conversion in both directions; and for anyone who values keeping a dry track on hand so a mix stays open to new ideas. Capture clean, reamp freely, and let the tone decisions wait until you are ready to make them.