Radial Engineering JDI Stereo - Jensen Equipped 2-channel Passive Instrument Direct Box-1

Radial JDI Stereo 2-Channel Passive Jensen Direct Box for Instruments

Radial Engineering ProAV2 2-channel Passive A/V Direct Box-1

Radial ProAV2 Passive Stereo Multimedia DI Direct Box

Radial ProAV1 Passive Multimedia DI Direct Box

Home DI Boxes / Transformers Radial ProAV1 Passive Multimedia DI Direct Box
was $210.00 Special Price $179.99

Passive Multimedia Direct Box, Stereo-to-Mono Summing, Eclipse ET-DB2 Transformer Isolation, 1/4-Inch / RCA / 3.5-mm / XLR Line Inputs, Balanced Mono XLR Output, Switchable Input Pad, Ground Lift, 1/4-Inch and RCA Thru, 128 dB Dynamic Range, No Power Required, 14-Gauge Steel Chassis

Availability: In Stock
SKU
ProAV1

 

 

Radial products purchased by an authorized Radial Engineering reseller include a 3 year, transferable warranty.

Radial ProAV1 Features:

  • PASSIVE MULTIMEDIA DIRECT BOX — Connect almost any audio source to a PA or mixer with a transformer-based design that needs no power, battery, or adapter.
  • STEREO-TO-MONO SUMMING — Left and right inputs are summed through a resistive mixer to one mono XLR output, halving the channel count a stereo device would need.
  • SWISS-ARMY INPUT PANEL — Dual 1/4-inch, RCA, 3.5-mm stereo, and line-level XLR inputs interface with laptops, media players, instruments, and console outputs adapter-free.
  • ECLIPSE TRANSFORMER ISOLATION — A custom Eclipse ET-DB2 transformer stays linear from 20 Hz to 18.5 kHz and eliminates hum and buzz from ground loops.
  • HANDLES HOT DIGITAL SOURCES — A 128 dB dynamic range and switchable input pad absorb signal peaks up to +18 dB so hot line levels stay clean and natural.
  • GROUND LIFT AND THRU JACKS — A ground-lift switch kills hum while 1/4-inch and RCA thru connections feed a stage amp or local monitor alongside the XLR feed.
  • ROAD-PROOF STEEL CHASSIS — A 14-gauge steel chassis and shell take the abuse of touring and permanent installation alike.

Radial ProAV1: A Passive Multimedia Direct Box That Sums Stereo to Mono

The Radial ProAV1 is a passive multimedia direct box (DI) that connects almost any audio source to a PA or mixer while automatically summing stereo signals to a single mono output. Purpose-built for audio-video integrators, it accepts 1/4-inch, RCA, 3.5-mm, and line-level XLR inputs, isolates them through a custom Eclipse transformer, and delivers one clean, balanced XLR feed, halving the channel count a stereo source would normally demand. When a presentation, playback rig, or install needs a stereo device to land on a single quiet mixer channel, the ProAV1 makes the connection instantly and without hum.

What a Direct Box Actually Does

A direct box performs three jobs that make consumer and instrument-level gear behave on a professional system. It converts high-impedance, unbalanced signals to the low-impedance, balanced signal a mixer expects, so tone stays full and noise cancels over a long cable run. It matches levels so a phone, laptop, or media player does not swamp a mic input. And it isolates grounds, breaking the loops between a computer or playback deck and the console that cause 60-cycle hum. The ProAV1 does all three passively, with no power required.

Why Passive and Transformer-Based

The ProAV1 is built around a custom Eclipse ET-DB2 transformer with a 12-to-1 ratio, and being passive means it needs no phantom power, battery, or adapter to work. That transformer is engineered to handle the extreme dynamics and wide frequency range of modern digital sources, staying linear from 20 Hz to 18.5 kHz with a huge 128 dB dynamic range and just 0.01 percent distortion. It absorbs signal peaks up to plus 18 dB without strain, so even a hot line output arrives clean, natural, and free of the harshness digital gear can produce.

Stereo-to-Mono Summing: One Channel, Not Two

The defining feature of the ProAV1 is its mono-sum design. A stereo source, a laptop, media player, or playback deck, arrives on the left and right inputs and is summed through a resistive mixer to one mono output. For an AV integrator this is the whole point: a stereo device that would normally eat two mixer channels now needs only one, cutting the channel count on a snake or console in half and simplifying the entire signal path. Where mono coverage is all a room needs, the ProAV1 gets a stereo device there on a single balanced line.

The Swiss-Army Input Panel

Connectivity is where the ProAV1 earns its place in a toolkit. Inputs are available on dual 1/4-inch, RCA, 3.5-mm stereo, and line-level XLR, so it can take a guitar or keyboard, a media player, a laptop headphone jack, or a plus-4 dB line output from a console or interface, all without hunting for adapter cables. Whatever the source device presents, the ProAV1 already has the jack for it, which is exactly what an integrator needs when the room's gear is unknown until load-in.

Input Pad, Ground Lift, and Thru Connections

An input pad tames sources that run too hot for the transformer, so a loud line output stays clean rather than overloading. A ground-lift switch breaks the hum-causing loop between the source and the mixer for silent operation on electrically noisy systems. And 1/4-inch and RCA thru connections pass the signal onward, so you can feed a stage amp or a local monitor while the balanced XLR runs to front of house. Every control earns its place on a box meant to solve real integration problems.

AV Integration and Instrument Duty

In an AV install or event, the ProAV1 is the reliable bridge between consumer playback gear and the professional PA, quietly summing stereo sources to mono and feeding the console on one channel. But it also works as a standard direct box for passive and active instruments, a guitar, bass, or keyboard plugs into the 1/4-inch input, thrus to an on-stage amp, and sends a clean isolated feed to the desk. One compact box covers both the presentation rig and the backline.

Who the ProAV1 Is For

The ProAV1 is for the AV integrator who needs to land stereo playback devices on a mono system without wasting channels; for the event and house-of-worship tech who wants a bulletproof, no-power box to connect laptops and media players to the PA; and for the musician who needs a quiet, rugged DI for instruments on stage. When a stereo source has to become one clean, hum-free mono channel, the ProAV1 is the passive direct box that does it.

More Information
MPN R800 1112
Input Multi
Power Source Passive
Form Desktop
Output XLR
Channels 2
UPC / EAN 676101036530
Brand Radial Engineering
Product Condition New
Availability In Stock

Radial ProAV1 Specifications

TypePassive multimedia direct box (DI)
Audio CircuitPassive, transformer based
TransformerEclipse ET-DB2, 12:1 ratio
ChannelsSingle channel (mono sum)
Frequency Response20 Hz - 18.5 kHz (+/- 0.2 dB)
Dynamic Range128 dB
THD0.01% from 20 Hz - 20 kHz @ -10 dB
Phase Deviation1 degree @ 100 Hz; 8 degrees @ 20 Hz
Input Impedance140k ohms, unbalanced
Output Impedance150 ohms, balanced
Common Mode Rejection100 dB @ 60 Hz
Maximum Input+18 dB @ 20 Hz
Input Connectors1/4-inch, RCA, 3.5-mm TRS, XLR
Output ConnectorsBalanced XLR
ControlsInput pad, mono sum, ground lift
Extras1/4-inch thru, RCA thru
PowerPassive, no power required
Chassis14-gauge steel chassis and shell